Enerdrive 20A AC & 40A DC RV60 DIY Installation Kit, With ePRO Plus Battery Monitor & Low Battery Cut Out

Enerdrive 20A AC & 40A DC RV60 DIY Installation Kit, With ePRO Plus Battery Monitor & Low Battery Cut Out, 5 Year Warranty. Introducing Enerdrives RV Installation Kits for 4WD Canopies, Caravans, Camper Trailers, Commercial Work Vehicles and more. Enerdrive have created many different layouts to fit nearly every possible application. Designed for the DIY handyman with basic electrical knowledge through to the professional looking to save installation time. You can choose kits ranging from 20A AC & 40A DC chargers through to 40A AC & DC units with monitoring and Low Battery Cutout. These kits are all pre-wired by Enerdrive where possible to keep the kits simple to install. All RV boards have a full wiring diagram showing each circuit and where to connect your loads, battery and inverter cabling. All items are mounted on a 12mm Black plastic (water & rot resistant) board for simple mounting into the application. Enerdrive also have you covered from a service and support angle with the RV Installation kits. Designed, constructed and pre-wired by Enerdrive, we know exactly the layout and wiring of your kit so any fault finding or support can be given quickly and concisely. Items Included K-RV060 K-RV060-01 K-RV060-02 K-RV060-03 ePOWER AC 20Amp 230v Charger * * * * ePOWER AC 40Amp 230v Charger ePOWER DC2DC 40+ Charger (Vehicle/Solar) * * * * ePRO Plus 500A Battery Monitor with Remote Display, with Audible & Visual Alarm * * * ePOWER AC Charger 30A Output Fuse Connection * * * * ePOWER AC Charger 50A Output Fuse Connection ePOWER DC2DC 60A Output Fuse Connection * * * * 50A Load Output Fuse Connection * * * * 8 Circuit “Wedge” Fuse Block * Low Battery Cutout (Programmed in ePRO Plus via Users Data Input) * 12mm Black Plastic Mounting Board. Water & Rot Resistance * * * * Dimensions 480L x 400W x 100Dmm 480L x 400W x 100Dmm 480L x 400W x 100Dmm 480L x 400W x 100Dmm Weight (*) Indicates Standard Fitment Enerdrive ePOWER 12V 40A DC to DC Battery Charger: Enerdrive ePOWER 12V 40A DC to DC Battery Charger designed to meet the rugged demands of Australian conditions and delivering multiple source charging for DC systems. The Enerdrive ePOWER DC2DC Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. 12V 40A DC2DC Battery Charger Features Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output DC M6 screw terminals that will allow for large battery cable connection between all sources A dedicated Maximum Power Point (MPPT) solar regulator The same battery algorithms as included in Enerdrives AC mains ePOWER battery charger including a specific lithium charging profile 40A output up to 40+°C with thermo controlled fan cooling Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage Temperature sensor included in charger for more accurate battery charging For In Vehicle & Marine Wiring Diagram, click below: For Towed Vehicle Wiring Diagram, click below: Enerdrive ePOWER 12V 20A Battery Charger : The Enerdrive ePOWER 20A Battery Charger is a fully automatic, “set and forget” charger. It is designed to quickly and accurately recharge your batteries using algorithms that help maximise service life. Multistage smart charging technology enables the charger to be connected to your battery banks permanently. As dictated by battery manufacturer’s recommendations, batteries require a multistage charge sequence for perfect, fast and accurate charging. The Enerdrive ePOWER charger can be programmed for Lithium batteries. This setting delivers the full rated output of the charger constantly with the charger switching to power supply mode once the voltage peak is met (indicating a full battery bank). 20A Battery Charger Features: Multistage Charging: Fully automatic multistage 20A battery charger with the ability to charge 3 separate battery banks. Separate Battery Banks: Isolated charging design where battery bank one is separate from battery bank two and three. Programmable: Battery bank 1 can be programmed with a different charge algorithm over banks 2 and 3. Current Control: User adjustable current output (e.g. Dial the 60amp unit back to run off a 1kVA generator). Smart Charging: The ePOWER 20A battery charger will regulate its output based on the loads connected to your battery banks. Wide AC Input Range: Operates on both 110V / 60Hz and 240V / 50Hz. LED Display: Easy to use “set and select” menu along with scrolling charger status. Silent Mode: Disables the cooling fan for total silent operation at night or whenever required. Activation reduces charge output by half and locks out fan for 12 hours. Temperature Sensor: Battery temperature sensor included with 3 meter cable. 2 Year Warranty from an Australian company renowned for customer support. Enerdrive ePRO PLUS Battery Monitor: The ePRO PLUS is the latest generation, highly advanced battery monitor. It consists of an intelligent shunt and a remote control display unit. The shunt has a Grid Optimized footprint for perfect integration with our DC Modular products. This advanced battery monitor not only shows the true state of charge of your battery system. It also offers a large amount of additional features to optimally supervise your battery system and control external equipment. The ePRO PLUS is compatible with lead based and Lithium batteries (LiFePO4). The ePRO PLUS can monitor up to three battery banks. The inputs for battery bank 2 and 3 can also be configured for other purposes, like mid-point voltage measurement, keyswitch input, setup lock or backlight control. The ePRO PLUS battery monitor can measure DC currents up to 600Amps (500Amp continuous) and voltages up to 70Vdc. So any lead- or lithium based battery from 12V up to 48V can be monitored. The installation time is minimal, requiring only one supply wire to the intelligent shunt base and a single ‘QuickLink’ cable between the shunt base and the control/display unit (CDU). Additionally, the battery minus cable must be interrupted in order to insert the shunt into the high current circuit. The fused supply wire and the QuickLink cable are both included in the package, avoiding the need for a separate connection kit. Complete battery status information at a glance (%, V, A, Ah, W, h:m, °C) Supports up to three battery banks (12V, 24V and 48V) Very simple ‘Plug and Play’ installation Perfect integration with Enerdrive DC Modular products Blue Sea ST Blade Fuse Block 12 Circuits with Negative Bus & Cover Consolidates branch circuits and in-line fuses: Positive distribution bus with #10-32 stud Can be used for 24-hour circuits Models available with or without a cover Cover satisfies ABYC/USCG requirements for insulation, incorporates an easy to open push button latch providing easy access to fuses, storage for two spare fuses, and label recesses that accept Blue Sea Systems” Small Format Labels for circuit identification Fuse blocks with covers include 20 write-on circuit labels Tin-plated copper buses and fuse clips Accepts ring or spade type terminals Accepts ATO® and ATC® fast acting blade fuses Fuses sold separately Enerdrive ePOWER 12/24V 40A Low Battery Cutout IP66 : The ePOWER Low Battery Cutoff protects your batteries from non essential loads before the battery is completely discharged causing damage to batteries and potently denying your engine cranking power. These Low Battery Cutouts also protect connected electrical appliances against over voltage. The voltage load is disconnected whenever the DC voltage goes beyond 16V (12V mode) or 32V (24V mode). Microprocessor Controlled: The ePOWER LBC is microprocessor controlled with 10 different programs that engage or disengage the voltage load over several different voltage paramaters. Features: Overvoltage Protection Ignition proof (no relay, no spark) Delayed alarm output Delayed load disconnect Applications: Recreational vehicles Service vehicles Maritime applications